4-step RF power selection
The IC-E92D provides 5W (typ.) output power both in VHF/UHF bands. The supplied BP-256 provides up to 6/5.5 hours* of operating time. When you don't need full power operation, you can reduce output power to 2.5/0.5/0.1W (typ.) for saving battery consumption.
* VHF/UHF single mode, Tx high: Rx: Stand-by duty ratio= 1: 1: 8

Retained features

Wide band receiver with dualwatch capability
The IC-E92D has dualwatch receiver capability, allowing you to receive two bands simultaneously (V/V, U/U, V/U possible). By pushing and holding the [Main/Dual] button, you can easily turn on/off the dualwatch mode, while a press of the button allows you to toggle the active VFO channels. When in the dualwatch mode, the operating frequency and mode are restricted to 495kHz–999.990MHz in FM/WFM/AM mode (VFO A) and 118–174MHz or 350–470MHz in FM/FM-N/AM/DV mode (VFO B)*.
* See specifications page for receive range coverage.

Large dot-matrix LCD
Using a large full dot-matrix LCD (37.8 × 20 mm), the IC-E92D clearly shows two line frequency settings, alphanumeric channel name, bandscope, received short data message and GPS coordination, etc. You can change the display setting to show frequency or memory name in the center of the display. In addition automatic LCD and keypad backlight provides bright illumination for night time

Total 1304 memory channels
The IC-E92D has a total 1304 memory channels with 26 memory banks. The VFO A has 800 regular channels, 50 scan edges and 2 call channels, while the VFO B has 400 regular, 50 scan edges and 2 call channels. All memory channels, memory banks and even scan edges can be named with 8-character channel comments

Simple bandscope
Spectrum activity is visually shown on the screen and AF output is emitted while sweeping the range. It is useful for finding new or interfering signals

Keypad navigation
The 4-direction cursor buttons on the keypad gives you quick and intuitive access to many settings. The twin volume/channel knob provides convenient channel/volume setting

External DC power jack
An external DC power jack allows for operation with an external DC power supply (10–16V DC). When used with the CP-19, CP-12L or OPC-254L, simultaneous operation during charging is possible.

Built-in CTCSS/DTCS encoder and decoder
CTCSS and DTCS tones are used for accessing a closed repeater or tone squelch operation. The pocket beep alerts you with a beep sound when the transceiver receives a preset tone

Multiple scan functions
The IC-E92D supports various scan types for maximum reception and ease of use.
• Full scan • Selected band scan • Programmed scan • Memory scan • Memory mode scan • All bank scan • Selected bank scan • Tone scan • Bank link scan (DMS) • Program scan link • Skip scan • Priority scan

Other features
• Squelch release function to monitor a weak signal. • Auto power save, power off and power on • 10 channel DTMF memory (16-digit) • 10dB (approx) built-in attenuator

DIGITAL FEATURES

D-STAR DV mode available (Digital Voice + data)
The IC-E92D provides DV mode operation with an AMBE codec. 950 bps data can be sent simultaneously with the digital voice transmission. The IC-92AD/E92D is compatible with the JARL D-STAR format*. In addition, when you receive an FM mode (or other mode) signal while operating in DV mode, the automatic DV detection function automatically changes the operating mode to the detected mode.
* The Digital features of the IC-E92D are compatible with IC-E91 series (With UT-121), IC-E2820 series (with UT-123), ID-800H, IC-V82/U82 (with UT-118) and IC-2200H (with UT-118).

GPS position reporting function
When connecting an optional HM-175GPS, own and other station’s position information can be sent and received*. The IC- 92AD/E92D sends the position data either by holding the PTT switch, or at a preset interval (5 seconds–30 minutes), depending on the setting.
* GPS data receive only is possible when no external GPS receiver or GPS speaker-microphone is attached.
Plotting position information on mapping software
When connected to a PC* via the optional RS-232C cable, OPC-1799, the position information can be plotted on mapping software* on a PC.
* Serial port and position mapping software (NMEA 0183 format) are required.
GPS alarm
The GPS alarm sounds when your own position is close to the specified point or area.

One touch reply button
The IC-E92D has a one-touch reply function. It uses the received callsign (including repeater callsign) and allows you to call back to the calling station without hassle. In addition, up to 20 received callsigns are stored as the received call record

Built-in voice recorder and auto reply
The IC-E92D has a built-in voice recorder*. It records an incoming call in DV mode for up to 30 seconds (approx.), or can be partitioned into 3 tracks (10 seconds each). The 10-second transmit memory allows you to record your callsign, CQ and automatically answers when you receive a message. (* Available in DV mode only)

Optional PC remote control capability (Also available in analog mode)
When the IC-E92D is connected to a PC via a RS-232C cable, most functions of the IC-E92D can be controlled from the PC. In DV mode operation, you can send and receive short messages of 20 characters (Max.) on the PC

DX communication over the D-STAR system
The 144, 440MHz D-STAR repeater is now available. It allows you cross band (144 /440/1200MHz) operation and long distance communication over the D-STAR system.

SPECIFICATIONS

GENERAL

Frequency coverage and Mode	: (Unit: MHz) Version Transmit Receive (Working range) Europe 144–146, 430–440 VFO A: 0.495–999.990 VFO B: 118–174, 350–470   Export 137–174, 400–470 VFO A: 0.495–999.990 VFO B: 118–174, 350–470
Mode	: FM, FM-N, WFM*1, AM*1 DV *1 Receive only,
Memory channels	: 1304 channels (including 100 program scan edges and 4 call channels)
Useable temp. range	: –20°C to +60°C;
Frequency stability	: ±2.5ppm (–20°C to +60°C)
Power supply External DC power	: 7.4V DC (with BP-256)   10–16V DC
Current drain (at 7.4V DC)	: Tx High (VHF/UHF) Rx FM (Single) DV (Single) FM/FM (Dual) FM/DV (Dual) 1.8/2.1A typ. Power save(Duty= 1:4)/Rated output/Stand-by 38mA/150mA/65mA typ. 47mA/200mA/110mA typ. 43mA/180mA/90mA typ. 50mA/200mA/110mA typ.
Tuning steps (kHz)	: 5*, 6.25*, 8.33*, 9*, 10, 12.5, 15, 20, 25, 30, 50, 100, 125, 200 * Not available on all bands or modes.
Antenna impedance	: 50Ω (SMA)
Dimensions (W×H×D)	: 59×112×34.2 mm
Weight (approx.)	: 325g; (with antenna and BP-256)

TRANSMITTER

Output power	: High 5W typ. Mid 2.5W typ.   Low 0.5W typ. Slow 0.1W typ.
Spurious emissions	: Less than –60dB
Max. freq. deviation	: ±5.0/2.5kHz (FM Wide/narrow)
Ext. MIC connector	: 2kΩ

RECEIVER

Intermediate frequency	: VFO A WFM VFO B 61.65MHz/450kHz (Except WFM) 59.25MHz/13.35MHz/1.95MHz 46.35MHz/450kHz
Sensitivity (typical)	FM (at 12dB SINAD, 3.5kHz DEV)   VHF (Ham band) 0.14μV   UHF (Ham band) 0.16μV   1.625–29.995MHz 0.4μV   30.000–75.995MHz 0.25μV   76.000–117.995MHz 0.25μV   118.000–173.995MHz* 0.14μV   174.000–259.995MHz 0.32μV   260.000–349.995MHz 0.32μV   350.000–469.995MHz* 0.16μV   470.000–599.995MHz 0.32μV   600.000–999.995MHz 0.56μV   (* Except ham bands)   WFM (at 12dB SINAD, 52.5kHz DEV)   76.000–108.000MHz 1μV   175.000–221.995MHz 1.8μV   470.000–770.000MHz 2.5μV     AM (at 10dB S/N, 30% Mod.)   0.495– 4.995MHz 1.3μV   5.000– 29.995MHz 0.56μV   118.000–136.995MHz 0.5μV   222.000–246.995MHz 0.79μV   247.000–329.995MHz 1μV
Selectivity	: AM/FM Wide FM-Narrow, DV WFM   More than 50dB More than 45dB More than 300kHz/–3dB Less than 700kHz/–20dB
Spurious and image rejection	: VHF (Ham band) UHF (Ham band) More than 60dB More than 50dB (IF more than 60dB)
Spurious radiation	: Less than –57dBm
Audio output power(7.4V DC)	: 200mW typ. at 10% distortion with an 8Ω load
Ext. speaker connector	: 8Ω

All stated specifications are subject to change without notice or obligation.
 

---